Select tubular Motor (Comparison table)

Choose RollerTrol Battery & Solar Motors

DIY Roller Blind Motors - FAQ

How To Insert Blind Motors & Attach Brackets

Calculate your Blind or Shade fabric Weight

Select Tube Size for Blind Motor

How to Insert Blind Motors Into Tube

How to Insert Blind Motors Into Tube with Adapters

Attach Mounting Brackets - Standard + Mini Series

Attach Mounting Brackets - MAXI Blind Series

How To Set Up Radio Equipped Blind & Shade Motors

Series P Radio Remote Control Motors

Series G Radio Remote Control Motors

Series R Radio Remote Control Motors

BroadLink RF/IR Hub System for Motors

How To Set Up Window/Skylight Openers

Introduction: Window & Skylight (K Series)

BroadLink RF/IR Hub System for Motors

Z-Wave Interfacing for Shade & Opener Motors

Wired Wall Switch Control of Window Openers

How To Use Alexa With Our Motors & Window Openers

How To Use BroadLink Phone App Hub With Our Motors

How To Set Up ShadeSlider Skylight or Bottom-Up Blind

How To Retrofit RV, Boat and Motorhome Blinds

How To Set Up Non-Radio Motors

Operation & Travel Limits of Non-Radio Motors

Make a Simple DC Motor Reversing Switch

How To Set Up ZWAVE Control

ZWAVE Controller for G Series Radio motors

ZWAVE Door/Window Opening Detection

ZWAVE Motion Detector with Temperature Sensing

Projects

Motorized Window Blinds & Shades

Motorized Dual Window Shade

Make Motorized Blackout Blinds

Phone-Tablet-PC Control for Motorized Blinds

Mini Motor for Existing Shade Retrofit

Roman Shade Retrofit

Make a Motorized Window Opener

Blind & Shade Motors for RV & Boats

Make Your Own Projector Screen

Curtain Closer: Ultimate Home Theater

Wireless Battery Operated Drapery Motor Kit

Make a Motorized Bottom-Up Shade

Make a Motorized Skylight Opener

BroadLink RF/IR Hub System for Motors

About

Why Buy From US?

Background & Mission Statement

Customer DIY Testimonials

Site Map - Search All Pages

Support

Why Buy From US?

RollerTrol Users Forum

Contact Page

Testimonials

Bulletin - ACTUATOR HAS BUILT-IN RAIN SENSOR

This is just a quick note to mention that we now have actuators with an INTEGRATED rain sensor. All you have to do is install and apply power. If rain falls on the sensor, it will close immediately. We also have a choice of actuators, depending on the weight of your skylight. See Skylight Motor Kits with rain sensor here .

The following article is a much more complicated way of doing it, but we have left it in place for legacy purposes.

This is the first article in this series about creating an IFTTT rain sensor monitoring system for a motorized skylight opener. This is done using the BroadLink ^® HA-RFIRW-5V automation hub phone app that controls our skylight/window openers, blind motors, smart film, drapery motors, and many other devices, such as fans and LED lights. In this article we will be discussing the rain sensing system applied to a typical example of a motorized skylight opener, such as the units you see in the picture at right. This customer used 2 actuators as his skylight was particularly heavy, but the extra weight could have been offset by counter-balances, springs or gas shocks. A single wireless rain sensor can be used to trigger the closure of multiple skylight motors (and windows), and each skylight can have a wireless magnetic sensor that will detect the closure action and report the status, just in case a component fails.

There are 5 main components to this system; the first 2 items are included in the BroadLink ^® SK1-WIFI-AC security kit:

The DW-RFISM-3VB wireless door/window open detection transmitter

The TR-RFISMW-AC transceiver hub that contains the IFTTT event reaction program that triggers the BroadLink ^® hub

The HA-RFIRW-5V BroadLink ^® controller hub that activates the skylight actuator motors by transmitting a radio signal to the actuator receiver

The WTK-12v-RR actuator kit (contains actuator, remote control, receiver & power supply

The RS-RFISM-12V rain sensor

If you didn't see the previous article series about using our HA-RFIRW-5V controller hub for home theater , you may be interested to review that series as this IFTTT rain sensor is an add-on to that system. You can also see more info about our motorized skylight/window actuators here.

The RS-RFISM-12V Rain Sensor

There are various different types of rain sensors on the market, and many of them are designed for blocking the operation of irrigation systems. Most of those designs are not suitable for this application because they measure the conductivity a sponge or porous material to determine that it is raining, and it takes a perhaps 5 to 10 minutes for the sensor to accumulate enough moisture to trigger the rainfall detection event. This works fine for irrigation purposes, but we need a much faster acting sensor for skylight closure. The metal surface detection plate of our RS-RFISM-12V rain sensor causes a trigger signal to be activated in less than a second, as soon as even a single drop of rain hits it. This fast acting response insures that your skylight will close quickly, as soon as it starts to rain, triggered by a digitally encoded signal transmitted from the sensor to the transceiver hub. The rain sensor unit is powered by 12v DC (red+, black-), and the output (yellow, white wires) will act like a normally open relay (electronic switch), closing the circuit when rain is detected. The optimum mounting angle is about 15°, to allow droplets to run off when it stops raining, and the output will swing open once the detection surface is dry, triggering another signal that can be used to open the skylight again, depending on environmental conditions.

The DW-RFISM-3VB Wireless Door/window Open Detection Transmitter

The on/off switch signal from the rain sensor has to be detected by the automation hub in some way, and our DW-RFISM-3VB magnetic door/window transmitting sensor provides an easy way to accomplish this. This is normally a two-part switch; the smaller part on the right contains a magnet, and the magnetic field is strong enough to cause a small reed relay to latch and close inside the larger unit - when it is in close proximity . One part is mounted on the door or window, and the other part is mounted on the frame, so that when the door or window (or skylight or any other object) is closed, the magnet is close enough to activate the relay. When the door/window is opened, the magnet is moved away from the relay, triggering a digital radio signal which is transmitted to the TR-RFISMW-AC transceiver hub. For this application of rain sensing, we will discard the magnet part and solder the output of the rain sensor to the reed relay terminals inside the main body of the door-window sensor. When the rain sensor detects water droplets, it will close the circuit, emulating the reed relay behavior, which will trigger a 'window closed' radio signal to be transmitted to the transceiver hub. You can open the main body of the door/window sensor simply by pressing the exposed tab; the back cover slides off. There are 3 visible screws that hold the circuit board in place; use a jeweller's screwdriver to remove the screws and lift out the circuit board. This exposes the reed relay, so you can solder your wires to it, but it also might be time to phone the geek.

The TR-RFISMW-AC Transceiver IFTTT Hub

This unit is the "event reaction" hub that receives the RF signal from the wireless transmitter that the rain sensor triggers. It is where the IFTTT (if-this-then-that) software resides, with a very user-friendly phone app to configure the event reaction commands. It can communicate via Wifi with the controller hub, instructing it to issue motor control commands or any other device you would like to control. This unit is AC powered and just simply plugs into any available outlet, and the antenna should be left in the vertical position. It will only connect to your router using the SmartConfig™ method; there is no alternative AP mode. Just enter your router SSID and password credentials and it will connect. We will cover the software setup in a subsequent article.

The HA-RFIRW-5V Controller Hub (not pictured)

If you didn't see the previous article series about using our HA-RFIRW-5V controller hub for home theater , you may be interested to review that series as this IFTTT rain sensor is an add-on to that system.

The WTK-12v-RR Actuator Kit (not pictured)

You can also see more info about our motorized skylight/window actuators here.

Where To Go From Here

The next article discusses the software setup of the IFTTT (if-this-then-that) alarm hub transceiver configuration , and the inclusion of the door and window opening sensor which will be re-purposed as a rain sensor input to the system.

Buy These Products In Our Online Store

If you are interested, you can purchase these products in our DIY online automation store .

Articles in this Skylight Rain Sensor series:

Part 1-Motorized Skylight Rain Sensor: Introduction (you are here )

Part 2-Skylight Rain Sensor Hardware Setup

Part 3-Skylight Rain Sensor Program Event Handling

Also, see the follow-on series about our other companion devices:

Using our HA-RFIRW-5V controller hub for home theater

IFTTT example: temperature and light sensitive blinds and shades

Wi-Fi Smart Plug with timers and IFTTT capabilities