[OpenWrt Wiki] MTS WG430223

link管理

链接快照平台

输入网页链接，自动生成快照
标签化管理网页链接

相关文章推荐

气宇轩昂的椅子 · Unplugged专辑上线&北之国VI限量版 ...· 1 月前 ·

爱跑步的鸡蛋 · Postgresql中常用的时间戳与日期的相 ...· 2 月前 ·

气宇轩昂的跑步鞋 · 智能博弈决策大模型智能体技术综述 - 专知VIP· 4 月前 ·

正直的镜子 · How to send a JSON ...· 4 月前 ·

无聊的刺猬 · 狗头萝莉前男友资源 - 搜狗图片搜索· 5 月前 ·

cd /tmp
for i in 1 2 3 4 5 6 7 8 9 10 11 12; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.1.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.1.2

192.168.1.2 - IP of the tftp server * Check backups in your tftp root folder. CAUTION:
If you have any third-party firmware (e.g. Padavan, Keenetic, AsusWrt, non-official OpenWrt community builds (especially for Breed bootloader) etc.) installed on your device it's strongly recommended to restore original OEM firmware (including bootloader, EEPROM, partition map etc.) from your backup before you start the OpenWrt installation on your device. 1. Login to the router web interface (superadmin:serial number) 2. Navigate to Administration → Miscellaneous → Access control lists & enable telnet & enable “Remote control from any IP address” 3. Connect to the router using telnet (default admin:admin) 4. Check the bootpartition:

uboot_env --get --name bootpartition

If the result is 1 then go to the next step, otherwise ( 0 ) - change the boot partition and reboot:

uboot_env --set --name bootpartition --value 1
reboot

5. Download and write the OpenWrt images:

cd /tmp
wget https://downloads.openwrt.org/releases/22.03.0/targets/ramips/mt7621/openwrt-22.03.0-ramips-mt7621-mts_wg430223-squashfs-factory.trx
mtd_write erase /dev/mtd4
mtd_write write openwrt-22.03.0-ramips-mt7621-mts_wg430223-squashfs-factory.trx /dev/mtd4

6. Set 1st boot partition and reboot:

uboot_env --set --name bootpartition --value 0
reboot

Under development 1. Login as root via SSH on 192.168.1.1, then enter the following commands:

fw_setenv bootpartition 1
reboot

2. Optional step. Upgrade the stock firmware with any version to overwrite the OpenWrt in Slot 1. * arccfg util unencrypts (cipher aes-128-cbc + some obfuscation) the configuration from mtd8(10) at every boot

~ # arccfg 
fgets partition name ok!the partition is [glbcfg] 
fgets the second partition name ok!the the second partition is [glbcfg2] 
The primary glbcfg is mtd8 
The second glbcfg is mtd10

* mtd9(11): board_data or board_data2 also contain MAC address (only *base* MAC). Other addresses should be calculated * @abyrga & @r3d5ky from telegram group Beeline SmarBox Giga found a way how to decrypt a partition. Issue

$ dd status=none if=mtd9 bs=1 count=368 skip=256 | openssl aes-128-cbc -d -nopad \
-K 2A4B303D7644395C3B2B7053553C5200 -iv 00000000000000000000000000000000
mac=ec:6c:##:##:##:b8
sn=AG##########
ssid=Beeline_2G_######
psk=###########
ssid2=Beeline_5G_######
psk2=###########
guest_ssid=Beeline_2G_######-Guest
guest_psk=###########
guest_ssid2=Beeline_5G_######-Guest
guest_psk2=###########
group_ssid=BH-Beeline_2G_######
group_psk=###########
group_ssid2=BH-Beeline_5G_######
group_psk2=###########
hw=01
password=#####

The same as Beeline Smartbox Flash but with another trx magic

+--------------+---------------+----------------------------------------+
| Offset       |               | Description                            |
+==============+===============+========================================+
| 0x0          | 31 52 48 53   | TRX magic "1RHS"                       |
+--------------+---------------+----------------------------------------+

→ bootloader * Ralink UBoot Version: 5.0.0.2 * U-boot protected by unknown password (hash 95f9f8f58a972c3bb653854cc54e85b4 ). Therefore, it isn't possible to load initramfs image or choose boot option except “3: Boot system code via Flash (default).”. * There is no any bootcounters

Browse to


     http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/

LuCI Upgrade URL

Upload image file for sysupgrade to LuCI

Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:


     sysupgrade

cd /tmp
wget https://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-mts_wg430223-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-ramips-mt7621-mts_wg430223-squashfs-sysupgrade.bin


    sysupgrade

does not support this router, use

mtd

cd /tmp
wget https://downloads.openwrt.org/snapshots/targets/ramips/mt7621/openwrt-ramips-mt7621-mts_wg430223-squashfs-factory.trx
mtd write /tmp/openwrt-ramips-mt7621-mts_wg430223-squashfs-factory.trx firmware && reboot

→ generic.debrick =================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL4 FB_DL: 0x4, 1/0 = 542/482 11000000 PLL3 FB_DL: 0x9, 1/0 = 604/420 25000000 PLL2 FB_DL: 0x14, 1/0 = 630/394 51000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 72 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00002120 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 7 7 7 10 6 8 8 6 3 6 10 | 7 7 7 9 7 7 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =32 DQS1 = 33 ================================================================== bit DQS0 bit DQS1 0 (2~59)30 8 (1~58)29 1 (1~63)32 9 (2~62)32 2 (1~61)31 10 (1~62)31 3 (1~63)32 11 (2~61)31 4 (1~60)30 12 (1~65)33 5 (1~60)30 13 (1~61)31 6 (1~61)31 14 (2~64)33 7 (1~63)32 15 (1~60)30 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 9 7 8 10 8 10 9 6 7 7 10 | 9 9 7 11 7 10 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Nov 2 2020 - 17:27:10) 0.00 Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f88000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 87fc85d0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [EF F1 00 95 00] Device found in MTK table, ID: eff1, EXT_ID: 9500 Support this Device in MTK table! eff1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 5.0.0.4 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Nov 2 2020 Time:17:27:10 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN LLLLW Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 3: System Boot system code via Flash[1]. ## Booting image at be300000 ... Verifying Trx ... OK Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4232464 Bytes = 4 MB Load Address: 81001000 Entry Point: 81801ae0 ................................................................. Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 81801ae0) ... ## Giving linux memsize in MB, 128 Starting kernel ... for led test (red off) ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A Ralink gpio driver initialized SSFDC read-only Flash Translation layer MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 81b644b0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [EF F1 00 95 00, 00009500] Device found in MTK table, ID: eff1, EXT_ID: 9500 Support this Device in MTK table! eff1 NAND device: Manufacturer ID: 0xef, Chip ID: 0xf1 (Unknown NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 in find_rootfs_partitions off=0x00300000 end=0x02300000 The trx header magic offset 0x00420000 MT7621-NAND: squash filesystem found at offset 0x00720000 Found image1 partition off 0x00720000 size 0x01be0000 in find_rootfs_partitions off=0x02300000 end=0x04300000 The trx header magic offset 0x00420000 MT7621-NAND: squash filesystem found at offset 0x02720000 Found image2 partition off 0x02720000 size 0x01be0000 Creating 13 MTD partitions on "MT7621-NAND": 0x000000000000-0x000007f80000 : "ALL" 0x000000000000-0x000000100000 : "Bootloader" 0x000000100000-0x000000200000 : "Config" 0x000000200000-0x000000300000 : "Factory" 0x000000300000-0x000002300000 : "Kernel" 0x000000720000-0x000002300000 : "RootFS" 0x000002300000-0x000004300000 : "Kernel2" 0x000002720000-0x000004300000 : "RootFS2" 0x000004300000-0x000004500000 : "glbcfg" 0x000004500000-0x000004600000 : "board_data" 0x000004600000-0x000004800000 : "glbcfg2" 0x000004800000-0x000004900000 : "board_data2" 0x000004900000-0x000007f80000 : "data" [mtk_nand] probe successfully! IMQ driver loaded successfully. (numdevs = 16, numqueues = 1) Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. PPP generic driver version 2.4.2 PPP BSD Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 register mt_drv == pAd = c0281000, size = 7712896, Status=0 == pAd->PciHif.CSRBaseAddress =0xc0180000, csr_addr=0xc0180000! RTMPInitPCIeDevice():device_id=0x7615 mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 AP Driver version-5.0.4.0 RtmpChipOpsHook(223): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use the default ePAeLNA bin image! Use the default /etc_ro/wlan/MT7615E_EEPROM1.bin bin image! <--mt7615_init() <-- RTMPAllocTxRxRingMemory, Status=0 rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288036 Ralink APSoC Ethernet Driver Initilization. v3.1 1024 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288036 PROC INIT OK! ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-platform: EHCI generic platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver *****run project phy. FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) FM_OUT value: u4FmOut = 0(0x00000000) xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd: irq 22, io mem 0x1e1c0000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: xHCI Host Controller usb usb1: Manufacturer: Linux 3.10.14 xhci-hcd usb usb1: SerialNumber: xhci-hcd hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: xHCI Host Controller usb usb2: Manufacturer: Linux 3.10.14 xhci-hcd usb usb2: SerialNumber: xhci-hcd hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage usbcore: registered new interface driver ums-alauda usbcore: registered new interface driver ums-sddr09 usbcore: registered new interface driver ums-sddr55 GACT probability on Mirror/redirect action on netem: version 1.3 u32 classifier Performance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. nfnl_acct: registering with nfnetlink. nf_conntrack version 0.5.0 (1843 buckets, 7372 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 ip_set: protocol 6 ipip: IPv4 over IPv4 tunneling driver gre: GRE over IPv4 demultiplexor driver ip_gre: GRE over IPv4 tunneling driver ip_tables: (C) 2000-2006 Netfilter Core Team Type=Restricted Cone ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver ip6_gre: GRE over IPv6 tunneling driver NET: Registered protocol family 17 Ebtables v2.0 registered l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 l2tp_ip: L2TP IP encapsulation support (L2TPv3) l2tp_netlink: L2TP netlink interface l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) 8021q: 802.1Q VLAN Support v1.8 Key type dns_resolver registered boot_part=1 /dev/mtdblock5 Boot from /dev/mtdblock7 VFS: Mounted root (squashfs filesystem) readonly on device 31:7. devtmpfs: mounted Freeing unused kernel memory: 236K (81b15000 - 81b50000) Arcadyan the primary config checkout succeed. Arcadyan the second config checkout succeed. arca.dbus.mng: is ready agent_handler(236):arca.dbus.misc: is ready Please press Enter to activate this console. MD5=[5db6aaf17d024c20b5025cbedbda1ef9] FFFFFFA4:FFFFFFCE:FFFFFFDA:65:43:21 Raeth v3.1 (Tasklet) set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 phy_free_head is 0xc1c000!!! phy_free_tail_phy is 0xc1dff0!!! txd_pool=a0c20000 phy_txd_pool=00C20000 ei_local->skb_free start address is 0x86d326cc. free_txd: 00c20010, ei_local->cpu_ptr: 00C20000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0c20000 0x00C20000 0x00C20000 phy_qrx_ring = 0x00c1e000, qrx_ring = 0xa0c1e000 phy_rx_ring0 = 0x00c28000, rx_ring[0] = 0xa0c28000 MT7530 Reset Completed!! change HW-TRAP to 0x17c8f set LAN/WAN LLLLW GMAC1_MAC_ADRH -- : 0x0000a4ce GMAC1_MAC_ADRL -- : 0xda654321 GDMA2_MAC_ADRH -- : 0x0000000c GDMA2_MAC_ADRL -- : 0x4328803a eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 GDMA2_MAC_ADRH -- : 0x0000a4ce GDMA2_MAC_ADRL -- : 0xda4c5a54 eth3: ===> VirtualIF_open ra0: ===> main_virtual_if_open load l1profile succeed! driver_own()::Try to Clear FW Own... driver_own()::Success to clear FW Own multi-profile merge success, en:1,pf1_num:2,pf2_num:4,total:6 Speed 100 ESW: Link Status Changed - Port3 Link UP , IF Name (eth2) , Speed (100) , Duplex (FULL) Open file "/etc/Wireless/RT2860/DBDC_card0.dat" to store DBDC cfg! (21) RT_CfgSetMacAddress : invalid length (0) RT_CfgSetMacAddress : invalid length (0) RT_CfgSetMacAddress : invalid length (0) RT_CfgSetMacAddress : invalid length (0) RT_CfgSetMacAddress : invalid length (0) E2pAccessMode=2 SSID[0]=MTSRouter_2.4G_654321, EdcaIdx=0 SSID[1]=MTSRouter_2G_654321-Guest, EdcaIdx=0 SSID[2]=MTSRouter_5G_654321, EdcaIdx=0 SSID[3]=MTSRouter_5G_654321-Guest, EdcaIdx=0 SSID[4]=MTSRouter_5G_Public2, EdcaIdx=0 SSID[5]=MTSRouter_5G_Public3, EdcaIdx=0 DBDC Mode=1, eDBDC_mode = 1 BSS0 PhyMode=14 wmode_band_equal(): Band Equal! BSS1 PhyMode=14 BSS2 PhyMode=49 BSS3 PhyMode=49 BSS4 PhyMode=49 BSS5 PhyMode=49 auto_ch_select_set_cfg(): BandIdx0, AutoChannelAtBootup=0, AutoChannelAlg = 0 auto_ch_select_set_cfg(): BandIdx1, AutoChannelAtBootup=0, AutoChannelAlg = 0 BandSteering=0 BndStrgBssIdx=0;0;0;0;0;0 [TxPower] BAND0: 100, BAND1: 100 Power Boost (CCK, OFDM): RTMPSetProfileParameters[PowerUpCckOfdm] BAND1: (0)-(0)-(0)-(0)-(0)-(0)-(0) Power Boost (HT20): RTMPSetProfileParametersPower Boost (HT40): RTMPSetProfileParametersPower Boost (VHT20): RTMPSetProfileParametersPower Boost (VHT40): RTMPSetProfileParametersPower Boost (VHT80): RTMPSetProfileParametersPower Boost (VHT160): RTMPSetProfileParameters[PERCENTAGEenable] BAND0: 1, BAND1: 1 [BFBACKOFFenable] BAND0: 0, BAND1: 0 CalCacheApply = 0 FragThreshold[0]=2346 FragThreshold[1]=2346 FragThreshold[2]=2346 FragThreshold[3]=2346 FragThreshold[4]=2346 FragThreshold[5]=2346 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 Valid=1 APAifsn[0]=3 APAifsn[1]=7 APAifsn[2]=1 APAifsn[3]=1 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 BSSAifsn[0]=3 BSSAifsn[1]=7 BSSAifsn[2]=2 BSSAifsn[3]=2 read_dscp_pri_param Setting Pri 7 for Dscp=52 read_dscp_pri_param Setting Pri 7 for Dscp=52 DfsZeroWait Support=0/0 DfsZeroWaitCacTime=255/255 RTMPSetProfileParameters(): ACSCheckTime[0]=0 seconds RTMPSetProfileParameters(): ACSCheckTime[1]=0 seconds read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[0] read_etxbf: MBSS[0] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 0 read_etxbf: BSSID[1] read_etxbf: MBSS[1] ETxBfEnCond = 0 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[2] read_etxbf: MBSS[2] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[3] read_etxbf: MBSS[3] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[4] read_etxbf: MBSS[4] ETxBfEnCond = 1 read_etxbf: ETxBfEnCond = 1 read_etxbf: BSSID[5] read_etxbf: MBSS[5] ETxBfEnCond = 1 [rtmp_read_ap_client_from_file] pf1=2 pf2=4 AndesSendCmdMsg: Could not send in band command due to diablefRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD AndesSendCmdMsg: Command type = ed, Extension command type = 48 HT: WDEV[0] Ext Channel = ABOVE HT: WDEV[1] Ext Channel = ABOVE HT: WDEV[2] Ext Channel = ABOVE HT: WDEV[3] Ext Channel = ABOVE HT: WDEV[4] Ext Channel = ABOVE HT: WDEV[5] Ext Channel = ABOVE HT: greenap_cap = 0 ICapMode = 0 WtcSetMaxStaNum: BssidNum:6, MaxStaNum:119 (WdsNum:0, ApcliNum:2, MaxNumChipRept:16), MinMcastWcid:120 Top Init Done! Use alloc_skb RX[0] DESC a0c14000 size = 16384 RX[1] DESC a0c12000 size = 8192 cut_through_init(): ct sw token number = 4095 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 859c3f08,859c3f08 cut_through_token_list_init(): TokenList inited done!id_head/tail=0/4096 cut_through_token_list_init(): 859c3f18,859c3f18 Hif Init Done! ctl->txq = c09d67b8 ctl->rxq = c09d67c4 ctl->ackq = c09d67d0 ctl->kickq = c09d67dc ctl->tx_doneq = c09d67e8 ctl->rx_doneq = c09d67f4 Parsing patch header Built date: 20180518100604a Platform: ALPS HW/SW version: 0x8a108a10 Patch version: 0x00000010 Target address: 0x80000, length: 11072 patch is not ready && get semaphore success EventGenericEventHandler: CMD Success MtCmdPatchFinishReq EventGenericEventHandler: CMD Success release patch semaphore WfMcuHwInit: Before NICLoadFirmware, check ICapMode = 0 Parsing CPU 0 fw tailer Chip ID: 0x04 Eco version: 0x00 Region number: 0x00 Format version: 0x00 Ram version: _reserved_ Built date: 20191220015534 Common crc: 0x0 Parsing tailer region 0 Feature set: 0x01 Target address: 0x84000, Download size: 409600 Parsing tailer region 1 Feature set: 0x01 Target address: 0x209c400, Download size: 48320 EventGenericEventHandler: CMD Success EventGenericEventHandler: CMD Success MtCmdFwStartReq: override = 0x1, address = 0x84000 EventGenericEventHandler: CMD Success Parsing CPU 1 fw tailer Chip ID: 0x04 Eco version: 0x00 Region number: 0x00Speed 1000 ESW: Link Status Changed - Port4 Link UP , IF Name (eth2) , Speed (1000) , Duplex (FULL) Format version: 0x00 Ram version: _reserved_ Built date: 20190415154149 Common crc: 0x0 Parsing tailer region 0 Feature set: 0x01 Target address: 0x90000000, Download size: 122608 EventGenericEventHandler: CMD Success MtCmdFwStartReq: override = 0x4, address = 0x0 EventGenericEventHandler: CMD Success MCU Init Done! efuse_probe: efuse = 10000212 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=1 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 NVM is FLASH mode. dev_idx [0] FLASH OFFSET [0x0] NICReadEEPROMParameters: EEPROM 0x52 b300 NICReadEEPROMParameters: EEPROM 0x52 b300 Country Region from e2p = 101 mt7615_antenna_default_reset(): TxPath = 4, RxPath = 4 mt7615_antenna_default_reset(): DBDC BAND0 TxPath = 2, RxPath = 2 mt7615_antenna_default_reset(): DBDC BAND1 TxPath = 2, RxPath = 2 RcRadioInit(): DbdcMode=1, ConcurrentBand=2 RcRadioInit(): pRadioCtrl=8738ef04,Band=0,rfcap=3,channel=1,PhyMode=2 extCha=0xf RcRadioInit(): pRadioCtrl=8738f20c,Band=1,rfcap=2,channel=36,PhyMode=1 extCha=0xf rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1 rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 0 TxBfModuleEnCtrl:i = 0, pRadioCtrl->IsBfBand = 1 TxBfModuleEnCtrl:i = 1, pRadioCtrl->IsBfBand = 0 TxBfModuleEnCtrl:u1BfNum = 1, u1BfBitmap = 1, u1BfSelBand[0] = 0 MtCmdSetDbdcCtrl:(ret = 0) MtSingleSkuLoadParam: RF_LOCKDOWN Feature OFF !!! MtBfBackOffLoadParam: RF_LOCKDOWN Feature OFF !!! EEPROM Init Done! mt_mac_init()--> mt7615_init_mac_cr()--> mt7615_init_mac_cr(): TMAC_TRCR0=0x82783c8c mt7615_init_mac_cr(): TMAC_TRCR1=0x82783c8c <--mt_mac_init() CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 CmdRxHdrTransBLUpdateRsp::EventExtCmdResult.u4Status = 0x0 MAC Init Done! MT7615BBPInit():BBP Initialization..... Band 0: valid=1, isDBDC=0, Band=2, CBW=1, CentCh/PrimCh=1/1, prim_ch_idx=0, txStream=2 Band 1: valid=0, isDBDC=0, Band=0, CBW=0, CentCh/PrimCh=0/0, prim_ch_idx=0, txStream=0 MT7615BBPInit() todo PHY Init Done! MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) WifiFwdSet::disabled=0 ap_ftkd> Initialize FT KDP Module... Main bssid = 00:00:00:00:00:00 MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) MtCmdSetMacTxRx:(ret = 0) <==== mt_wifi_init, Status=0 TxBfModuleEnCtrl:i = 0, pRadioCtrl->IsBfBand = 1 TxBfModuleEnCtrl:i = 1, pRadioCtrl->IsBfBand = 0 TxBfModuleEnCtrl:u1BfNum = 1, u1BfBitmap = 1, u1BfSelBand[0] = 0 MtCmdEDCCACtrl: BandIdx: 0, EDCCACtrl: 1 MtCmdEDCCACtrl: BandIdx: 1, EDCCACtrl: 1 WtcSetMaxStaNum: BssidNum:6, MaxStaNum:119 (WdsNum:0, ApcliNum:2, MaxNumChipRept:16), MinMcastWcid:120 RedInit: set CR4/N9 RED Enable to 1. RedInit: RED Initiailize Done. cp_support_is_enabled: set CR4 CP_SUPPORT to Mode 2. RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 0 wdev_attr_update(): wdevId0 = a4:ce:da:4c:5a:55 rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 1 rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 0 TxBfModuleEnCtrl:i = 0, pRadioCtrl->IsBfBand = 1 TxBfModuleEnCtrl:i = 1, pRadioCtrl->IsBfBand = 0 TxBfModuleEnCtrl:u1BfNum = 1, u1BfBitmap = 1, u1BfSelBand[0] = 0 MtCmdSetDbdcCtrl:(ret = 0) [RadarStateCheck] RD_NORMAL_MODE mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 6,control_ch2=0, central_chl = 8 DBDCIdx= 0, Band= 0 BW = 1,TXStream = 2, RXStream = 2, scan(0) [DfsCacNormalStart] Normal start. Enable MAC TX Caller: wlan_operate_init+0xa4/0x11c phy_mode=14, ch=6, wdev_type=1 ht_cap->HtCapInfo: ldpc=0,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap->HtCapParm: mdpu_density=5, ampdu_factor=3 AP inf up for ra_0(func_idx) OmacIdx=0 AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOn ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[0] = 0 ApAutoChannelAtBootUp<----------------- ap_run_at_boot() : ACS is disable !! [PMF]APPMFInit:: apidx=0, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkup(), wdev idx = 0 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 0, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 MtCmdSetDbdcCtrl:(ret = 0) UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 0 APStartUpForMbss: BssIndex = 0 channel = 6 MtCmdTxPowerDropCtrl: ucPowerDrop: 100, BandIdx: 0 [update_mgmt_frame_power] disable mgmt pwr ctrl apidx 0 for WscUUIDInit Generate UUID for apidx(0) ExtEventBeaconLostHandler::FW LOG, Beacon lost (a4:ce:da:4c:5a:55), Reason 0x10 Beacon lost - AP disabled!!! APStop(), oper(1) bssid(0)=a4:ce:da:4c:5a:55 wifi_sys_linkdown(), wdev idx = 0 ExtEventBeaconLostHandler::FW LOG, Beacon lost (a4:ce:da:4c:5a:55), Reason 0x10 Beacon lost - AP disabled!!! bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wifi_sys_close(), wdev idx = 0 MtCmdFdFrameOffloadSet(): Enable = 0, OwnMacIdx = 0, WlanIdx = 0, Band = 0, Len = 0 <=== APStop() AsicRadioOnOffCtrl(): DbdcIdx=0 RadioOff rax0: ===> mbss_virtual_if_open RTMP_COM_IoctlHandle -> CMD_RTPRIV_IOCTL_VIRTUAL_INF_UP wifi_sys_open(), wdev idx = 2 wdev_attr_update(): wdevId2 = a6:ce:da:2c:5a:55 rcUpdateBandForBFMU PhyCtrl[0].RadioCtrl.IsBfBand = 0 rcUpdateBandForBFMU PhyCtrl[1].RadioCtrl.IsBfBand = 1 TxBfModuleEnCtrl:i = 0, pRadioCtrl->IsBfBand = 0 TxBfModuleEnCtrl:i = 1, pRadioCtrl->IsBfBand = 1 TxBfModuleEnCtrl:u1BfNum = 1, u1BfBitmap = 1, u1BfSelBand[0] = 1 MtCmdSetDbdcCtrl:(ret = 0) [RadarStateCheck] RD_NORMAL_MODE mt7615_apply_cal_data() : eeprom 0x52 bit 1 is 0, do runtime cal , skip RX reload mt7615_apply_cal_data() : eeprom 0x52 bit 0 is 0, do runtime cal , skip TX reload MtCmdChannelSwitch: control_chl = 36,control_ch2=0, central_chl = 42 DBDCIdx= 1, Band= 0 BW = 2,TXStream = 2, RXStream = 2, scan(0) [DfsCacNormalStart] Normal start. Enable MAC TX Caller: wlan_operate_init+0xa4/0x11c phy_mode=49, ch=36, wdev_type=1 ht_cap->HtCapInfo: ldpc=0,ch_width=1,gf=0,sgi20=1,sgi40=1,tx_stbc=1,rx_stbc=1,amsdu_size=1 ht_cap->HtCapParm: mdpu_density=5, ampdu_factor=3 HcGetEdca(): wdev=0, hobj is not ready! :MtCmdPktBudgetCtrl: bssid(255),wcid(65535),type(0) AP inf up for ra_2(func_idx) OmacIdx=18 AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOn ApAutoChannelAtBootUp-----------------> ApAutoChannelAtBootUp: AutoChannelBootup[1] = 0 ApAutoChannelAtBootUp<----------------- ap_run_at_boot() : ACS is disable !! [PMF]APPMFInit:: apidx=2, MFPC=0, MFPR=0, SHA256=0 wifi_sys_linkup(), wdev idx = 2 wtc_acquire_groupkey_wcid: Found a non-occupied wtbl_idx:127 for WDEV_TYPE:1 LinkToOmacIdx = 12, LinkToWdevType = 1 bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 8192, CmdBssInfoBmcRate.u2McTransmit = 8192 MtCmdSetDbdcCtrl:(ret = 0) UpdateBeaconHandler, BCN_UPDATE_INIT, OmacIdx = 12 APStartUpForMbss: BssIndex = 1 channel = 36 MtCmdTxPowerDropCtrl: ucPowerDrop: 100, BandIdx: 1 [update_mgmt_frame_power] disable mgmt pwr ctrl apidx 2 for WscUUIDInit Generate UUID for apidx(2) ExtEventBeaconLostHandler::FW LOG, Beacon lost (a6:ce:da:2c:5a:55), Reason 0x10 Beacon lost - AP disabled!!! APStop(), oper(1) bssid(2)=a6:ce:da:2c:5a:55 wifi_sys_linkdown(), wdev idx = 2 ExtEventBeaconLostHandler::FW LOG, Beacon lost (a6:ce:da:2c:5a:55), Reason 0x10 Beacon lost - AP disabled!!! bssUpdateBmcMngRate (BSS_INFO_BROADCAST_INFO), CmdBssInfoBmcRate.u2BcTransmit= 0, CmdBssInfoBmcRate.u2McTransmit = 0 wifi_sys_close(), wdev idx = 2 MtCmdFdFrameOffloadSet(): Enable = 0, OwnMacIdx = 18, WlanIdx = 0, Band = 1, Len = 0 <=== APStop() AsicRadioOnOffCtrl(): DbdcIdx=1 RadioOff device eth2 entered promiscuous mode device eth3 entered promiscuous mode device ra0 entered promiscuous mode device rax0 entered promiscuous mode br0: port 4(rax0) entered forwarding state br0: port 4(rax0) entered forwarding state br0: port 3(ra0) entered forwarding state br0: port 3(ra0) entered forwarding state br0: port 2(eth3) entered forwarding state br0: port 2(eth3) entered forwarding state br0: port 1(eth2) entered forwarding state br0: port 1(eth2) entered forwarding state telnetd starting ... [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK [as_load_key_cert] load CERT/KEY files OK nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead. BusyBox v1.18.5 (2020-11-13 16:25:23 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. ~ # echo "FW=$(mng_cli get ARC_SYS_FWVersion).$(mng_cli get ARC_SYS_FWSubVersion FW=2.00.18MT201113 ~ # echo "FWdate=$(cat /usr/fwdate)" FWdate=Fri Nov 13 16:26:46 CST 2020 ~ # echo "Slot=$(uboot_env --get --name bootpartition)" Slot=1 ~ # echo "bootversion=$(uboot_env --get --name bootversion)" bootversion=5.0.0.4 ~ # echo "HW=$(arcbd get hw)" HW=01 =================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL4 FB_DL: 0x4, 1/0 = 641/383 11000000 PLL3 FB_DL: 0x9, 1/0 = 550/474 25000000 PLL2 FB_DL: 0x14, 1/0 = 643/381 51000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 15 rank 0 fine = 80 B:| 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 opt_dle value:11 DRAMC_R0DELDLY[018]=00002121 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 7 7 7 10 6 8 8 6 3 6 10 | 7 7 7 9 7 7 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =33 DQS1 = 33 ================================================================== bit DQS0 bit DQS1 0 (1~60)30 8 (1~58)29 1 (1~62)31 9 (2~62)32 2 (1~62)31 10 (2~62)32 3 (1~65)33 11 (2~60)31 4 (1~61)31 12 (2~65)33 5 (1~61)31 13 (1~60)30 6 (1~62)31 14 (2~62)32 7 (1~64)32 15 (1~61)31 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 10 9 9 10 8 10 10 7 7 7 10 | 8 9 7 12 8 9 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Nov 2 2020 - 17:27:10) 0.00 Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer at: 87f88000 Config XHCI 40M PLL ****************************** Software System Reset Occurred ****************************** Allocate 16 byte aligned buffer: 87fc85d0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [EF F1 00 95 00] Device found in MTK table, ID: eff1, EXT_ID: 9500 Support this Device in MTK table! eff1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 ..============================================ Ralink UBoot Version: 5.0.0.4 -------------------------------------------- ASIC MT7621A DualCore (MAC to MT7530 Mode) DRAM_CONF_FROM: Auto-Detection DRAM_TYPE: DDR3 DRAM bus: 16 bit Xtal Mode=3 OCP Ratio=1/3 Flash component: NAND Flash Date:Nov 2 2020 Time:17:27:10 ============================================ icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =128 Mbytes #Reset_MT7530 set LAN/WAN LLLLW Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 3: System Boot system code via Flash[0]. ## Booting image at bc300000 ... Verifying Trx ... OK Image Name: MIPS OpenWrt Linux-5.10.127 Image Type: MIPS Linux Kernel Image (uncompressed) Data Size: 2679498 Bytes = 2.6 MB Load Address: 80001000 Entry Point: 80001000 ......................................... Verifying Checksum ... OK No initrd ## Transferring control to Linux (at address 80001000) ... ## Giving linux memsize in MB, 128 Starting kernel ... for led test (red off) ... OpenWrt kernel loader for MIPS based SoC Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.10.127 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19523-bfd070e7fa) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Wed Jul 6 19:09:39 2022 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is MTS WG430223 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30256 r8192 d22992 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=00068800 [ 0.000000] Readback ErrCtl register=00068800 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 119536K/131072K available (6999K kernel code, 630K rwdata, 824K rodata, 1260K init, 243K bss, 11536K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000013] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.015856] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.033806] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.106127] pid_max: default: 32768 minimum: 301 [ 0.115434] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129838] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.148118] rcu: Hierarchical SRCU implementation. [ 0.157927] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.173495] smp: Bringing up secondary CPUs ... [ 0.183235] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.183245] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.183256] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.183333] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.243340] Synchronize counters for CPU 1: done. [ 0.305504] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.305513] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.305520] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.305568] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.364467] Synchronize counters for CPU 2: done. [ 0.424802] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.424811] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.424819] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.424871] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.484049] Synchronize counters for CPU 3: done. [ 0.543658] smp: Brought up 1 node, 4 CPUs [ 0.556001] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.575510] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.589338] pinctrl core: initialized pinctrl subsystem [ 0.602048] NET: Registered protocol family 16 [ 0.612031] thermal_sys: Registered thermal governor 'step_wise' [ 0.613370] cpuidle: using governor teo [ 0.636006] rt2880-pinmux pinctrl: there is not valid maps for state default [ 0.684099] clocksource: Switched to clocksource GIC [ 0.695857] NET: Registered protocol family 2 [ 0.704836] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.720276] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.736965] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.752111] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.766080] TCP: Hash tables configured (established 1024 bind 1024) [ 0.778848] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.791749] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.805861] NET: Registered protocol family 1 [ 0.814455] PCI: CLS 0 bytes, default 32 [ 0.824605] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.841651] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.853131] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.873441] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.889822] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.901199] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.912557] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.924619] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.941446] printk: console [ttyS0] disabled [ 0.949925] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.967835] printk: console [ttyS0] enabled [ 0.967835] printk: console [ttyS0] enabled [ 0.984384] printk: bootconsole [early0] disabled [ 0.984384] printk: bootconsole [early0] disabled [ 1.005801] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388 [ 1.020685] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xf1 [ 1.033368] nand: Winbond W29N01HV [ 1.040219] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.055300] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 1.068336] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 1.082890] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134 [ 1.097445] Scanning device for bad blocks [ 1.749717] 10 fixed-partitions partitions found on MTD device mt7621-nand [ 1.763406] Creating 10 MTD partitions on "mt7621-nand": [ 1.773988] 0x000000000000-0x000000100000 : "u-boot" [ 1.784891] 0x000000100000-0x000000200000 : "u-boot-env" [ 1.796612] 0x000000200000-0x000000300000 : "Factory" [ 1.807797] 0x000000300000-0x000002300000 : "firmware" [ 1.819121] 2 fixed-partitions partitions found on MTD device firmware [ 1.832145] Creating 2 MTD partitions on "firmware": [ 1.842035] 0x000000000000-0x000000440000 : "kernel" [ 1.852865] 0x000000440000-0x000002000000 : "ubiconcat0" [ 1.864565] 0x000002300000-0x000004300000 : "Firmware2" [ 1.876076] 0x000004300000-0x000004500000 : "glbcfg" [ 1.886959] 0x000004500000-0x000004600000 : "board_data" [ 1.898520] 0x000004600000-0x000004800000 : "glbcfg2" [ 1.909684] 0x000004800000-0x000004900000 : "board_data2" [ 1.921478] 0x000004900000-0x000007f80000 : "ubiconcat1" [ 1.940869] Concatenating MTD devices: [ 1.948383] (0): "ubiconcat0" [ 1.954295] (1): "ubiconcat1" [ 1.960184] into device "ubi-concat" [ 1.967367] 1 fixed-partitions partitions found on MTD device ubi-concat [ 1.980703] Creating 1 MTD partitions on "ubi-concat": [ 1.990937] 0x000000000000-0x000005240000 : "ubi" [ 2.045676] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.063488] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 2.081045] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 21 [ 2.098496] i2c /dev entries driver [ 2.108177] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 2.121571] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 2.139098] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 2.155416] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 2.171803] mt7621-pci 1e140000.pcie: Parsing DT failed [ 2.184680] NET: Registered protocol family 10 [ 2.195421] Segment Routing with IPv6 [ 2.202811] NET: Registered protocol family 17 [ 2.211821] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.238040] 8021q: 802.1Q VLAN Support v1.8 [ 2.249822] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 2.286096] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=26) [ 2.308183] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=27) [ 2.331062] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 2.347860] DSA: tree 0 setup [ 2.354127] rt2880-pinmux pinctrl: pcie is already enabled [ 2.365148] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 2.378510] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 2.396046] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 2.412336] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 2.428734] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 2.443828] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 2.458824] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 2.573380] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 2.584505] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 2.695742] mt7621-pci 1e140000.pcie: pcie0 no card, disable it (RST & CLK) [ 2.709609] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 2.723476] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 2.733192] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 2.751892] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 2.764576] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 2.778271] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 2.791960] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.802886] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 2.823197] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 2.835187] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 2.847670] pci 0000:00:00.0: reg 0x14: [mem 0x60100000-0x6010ffff] [ 2.860214] pci 0000:00:00.0: supports D1 [ 2.868199] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 2.881300] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 2.893331] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 2.907381] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 2.920032] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 2.950959] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 2.961391] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 2.973533] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 2.987060] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.000272] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 3.013446] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.027323] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 3.040840] pci 0000:00:00.0: BAR 1: assigned [mem 0x60100000-0x6010ffff] [ 3.054368] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 3.067892] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 3.082455] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.092348] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 3.105869] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.121700] UBI: auto-attach mtd12 [ 3.128554] ubi0: attaching mtd12 [ 3.135509] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 3.976449] ubi0: scanning is finished [ 4.000811] ubi0: attached mtd12 (name "ubi", size 82 MiB) [ 4.011808] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.025513] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.039037] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.052898] ubi0: good PEBs: 658, bad PEBs: 0, corrupted PEBs: 0 [ 4.064874] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.079262] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1657134579 [ 4.097452] ubi0: available PEBs: 0, total reserved PEBs: 658, PEBs reserved for bad PEB handling: 13 [ 4.115846] ubi0: background thread "ubi_bgt0d" started, PID 459 [ 4.118343] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.138828] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.160701] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.179046] Freeing unused kernel memory: 1260K [ 4.188136] This architecture does not have kernel memory protection. [ 4.200980] Run /sbin/init as init process [ 4.761693] init: Console is alive [ 4.768941] init: - watchdog - [ 5.462669] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.590081] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.614454] init: - preinit - [ 6.390464] random: jshn: uninitialized urandom read (4 bytes read) [ 6.474850] random: jshn: uninitialized urandom read (4 bytes read) [ 7.022554] random: jshn: uninitialized urandom read (4 bytes read) [ 7.358687] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 7.374926] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 7.384585] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 7.405255] 8021q: adding VLAN 0 to HW filter on device lan1 [ 7.419641] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 7.447872] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.982859] mt7530 mdio-bus:1f lan1: Link is Up - 100Mbps/Full - flow control off [ 8.998033] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready [ 11.722083] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 11.733681] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 586 [ 11.816839] UBIFS (ubi0:1): recovery needed [ 11.980728] UBIFS (ubi0:1): recovery completed [ 11.989767] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 12.005377] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 12.025116] UBIFS (ubi0:1): FS size: 75804672 bytes (72 MiB, 597 LEBs), journal size 3809280 bytes (3 MiB, 30 LEBs) [ 12.045890] UBIFS (ubi0:1): reserved for root: 3580441 bytes (3496 KiB) [ 12.059066] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID D3C4510B-B083-480C-9882-6C01CF484DB4, small LPT model [ 12.089020] mount_root: switching to ubifs overlay [ 12.120313] urandom-seed: Seeding with /etc/urandom.seed [ 12.318374] mt7530 mdio-bus:1f lan1: Link is Down [ 12.338103] procd: - early - [ 12.344231] procd: - watchdog - [ 13.024319] procd: - watchdog - [ 13.136577] procd: - ubus - [ 13.281049] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.305006] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.318188] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.334620] procd: - init - Please press Enter to activate this console. [ 14.167262] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.589228] urngd: v1.0.2 started. [ 14.602838] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace [ 14.618046] Backport generated by backports.git v5.15.33-1-0-g183c4ab2 [ 14.855362] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 14.866243] pci 0000:00:00.0: enabling device (0006 -> 0007) [ 14.871429] random: crng init done [ 14.877544] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 14.896357] random: 29 urandom warning(s) missed due to ratelimiting [ 14.925737] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 14.925737] [ 14.963493] PPP generic driver version 2.4.2 [ 14.974335] NET: Registered protocol family 24 [ 14.992409] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.196245] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 15.335265] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190121161307 [ 23.884142] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 23.910357] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 23.926568] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 23.937607] device eth0 entered promiscuous mode [ 23.953262] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 23.967757] 8021q: adding VLAN 0 to HW filter on device lan1 [ 23.982570] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.996117] br-lan: port 1(lan1) entered blocking state [ 24.007007] br-lan: port 1(lan1) entered disabled state [ 24.018607] device lan1 entered promiscuous mode [ 24.052261] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 24.066341] 8021q: adding VLAN 0 to HW filter on device lan2 [ 24.082678] br-lan: port 2(lan2) entered blocking state [ 24.093295] br-lan: port 2(lan2) entered disabled state [ 24.105952] device lan2 entered promiscuous mode [ 24.138111] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:04] driver [MediaTek MT7530 PHY] (irq=POLL) [ 24.157112] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii-rxid link mode [ 25.611394] mt7530 mdio-bus:1f lan1: Link is Up - 100Mbps/Full - flow control off [ 25.626532] br-lan: port 1(lan1) entered blocking state [ 25.637056] br-lan: port 1(lan1) entered forwarding state [ 25.650280] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 28.304400] mtk_soc_eth 1e100000.ethernet wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 28.321140] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready BusyBox v1.35.0 (2022-07-06 19:09:39 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt 22.03.0-rc5, r19523-bfd070e7fa ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/# ubus call system board "kernel": "5.10.127", "hostname": "OpenWrt", "system": "MediaTek MT7621 ver:1 eco:3", "model": "MTS WG430223", "board_name": "mts,wg430223", "rootfs_type": "squashfs", "release": { "distribution": "OpenWrt", "version": "22.03.0-rc5", "revision": "r19523-bfd070e7fa", "target": "ramips/mt7621", "description": "OpenWrt 22.03.0-rc5 r19523-bfd070e7fa" ramips mediatek mt7621 gigabitethernet wlan 3port 802.11abgn 802.11a 802.11bgn 802.11ac 128nand 128ram serial u-boot arcadyan dbdc mt7615dn Dual firmware mts

OEM easy installation

OEM firmware trx format

Original bootloader

Debricking